WebStructural

Cut and Fill Calculator

Draw a building pad on the map and get cut, fill and truckloads from USGS lidar.

Find the site, then press Draw the pad and click its corners. Click the first corner again to close it. Drag the corners to change it.

Cut and fill

Draw the pad to see the cut and fill.

3D site model

Draw the pad to see it on the ground in 3D.

Soils, flood zones and wetlands

Draw the pad to see the soils, flood zones and wetlands around it.

Site

Pad

The finished subgrade of the pad. Balance finds where the cut makes the fill.

Soil and trucks

Swell is how much the dirt grows loose in a truck. Shrink is how much it loses when compacted as fill.

How the calculator works

The ground comes from the USGS 3D Elevation Program’s 1 m lidar, bare earth with buildings and trees removed. Where a site has no 1 m lidar, the USGS 10 m model fills in and the calculator says so.

The pad is flat at the elevation you set. From its edge, the cut slope rises and the fill slope falls until each meets the ground at the daylight line. Ground above the cut slope is cut and ground below the fill slope is filled. Topsoil is stripped from everything disturbed first, and the cut and fill are measured from the stripped ground, one square meter of lidar at a time.

Cut is measured in the ground and fill compacted in place. Shrink converts one to the other, so Balance finds the pad elevation where the cut, once compacted, just makes the fill. Swell gives the loose volume in the trucks.

Pro accounts can also upload the pad from a CAD drawing saved as a Drawing Exchange Format (DXF) file, or from a comma-separated values (CSV) or Excel sheet of its corners. The corners can be in State Plane, Universal Transverse Mercator (UTM), longitude and latitude, or local coordinates. Anyone can draw a pad of about an acre and see the heat map and the 3D model. The volumes, import or export and truckloads are part of Pro, which also goes up to about 20 acres, saves pads in folders and makes a PDF report. The numbers are estimates for planning and early pricing. Ground graded since the lidar was flown isn’t in them, so check against a site survey before bidding. For the method step by step, with a worked example, see how to calculate cut and fill.

Upload the pad

Upload the pad’s outline and the calculator puts it on the map and reads the ground under it.

CAD drawing, as a DXF
A Drawing Exchange Format (DXF) file with the pad as one closed polyline, from AutoCAD, Civil 3D, MicroStation or any other CAD program. A layer named PAD is used first; otherwise the largest closed outline, and you can pick another. The polyline’s elevation becomes the pad elevation. Have a DWG? Save it as a DXF first.
Spreadsheet: CSV or Excel (.xlsx)
A comma-separated values (CSV) or Excel file with one row per corner, in order around the pad. Head the columns X and Y, Easting and Northing, or Longitude and Latitude, with an Elevation column if you like. A survey export without headings (point, northing, easting, elevation, description) works too.
123456 Pad Easting (X) Northing (Y)
Point,Easting,Northing,Elevation
1,1000.0,5000.0,410.0
2,1180.0,5000.0,410.0
3,1180.0,5080.0,410.0
4,1100.0,5080.0,410.0
5,1100.0,5120.0,410.0
6,1000.0,5120.0,410.0

Go around the pad in order, either way. There’s no need to repeat the first corner at the end.

Coordinates
State Plane or Universal Transverse Mercator (UTM), in feet or meters: the zone is worked out from where the map is, so find the site first. Longitude and latitude work as they are. A local site grid is set down in the middle of the map, north up, for you to drag into place.