# How to Calculate the Topographic Factor Kzt: ASCE 7 Worked Example

Source: https://webstructural.com/how-to-calculate-kzt.html

> How to calculate the topographic factor Kzt to ASCE 7-16 and 7-22 section 26.8: the five conditions, H, Lh and x, K1, K2 and K3 from Figure 26.8-1, and a worked example on the Palisades cliff above the Hudson River.

Wind speeds up as it climbs a hill, a ridge or a cliff. A building near the top of one gets more wind pressure than the same building on flat ground. ASCE 7 accounts for this with the topographic factor K_zt, which multiplies the velocity pressure q_z. On flat ground K_zt is 1.0. Near the edge of a steep cliff it can be close to 2, which nearly doubles the wind pressure.

This tutorial follows ASCE 7-16 and ASCE 7-22 section 26.8 and Figure 26.8-1, which use the same method. It covers when K_zt applies, how to read H, L_h and x off the ground, and a worked example on a real cliff.

[![The topographic factor calculator at the Palisades site: a 3D satellite view from over the Hudson River of the cliff face, with the governing northeast wind line running up the cliff past the half-height point to the crest, and K_zt = 1.94 with H and L_h beside it.](https://webstructural.com/images/tutorials/kzt/calculator-palisades.webp)](https://webstructural.com/topographic-factor-calculator.html?lat=40.98750&lon=-73.90650&height=30&exposure=C)

The worked example below, in our [topographic factor calculator](https://webstructural.com/topographic-factor-calculator.html?lat=40.98750&lon=-73.90650&height=30&exposure=C): K_zt = 1.94 at the edge of the Palisades cliff.

## The three shapes

ASCE 7 sorts the ground into three shapes. Each has its own factors in Figure 26.8-1.

- **2D ridge:** a long ridge across the wind, with ground falling away on the downwind side.
- **2D escarpment:** a cliff or steep slope up to a plateau that stays high downwind.
- **3D axisymmetric hill:** a hill the wind can also go around, with ground falling away on all sides.

Three distances describe the ground, each measured along the wind:

- **H** is the height of the hill or escarpment above the upwind ground (its base).
- **L_h** is the horizontal distance upwind from the crest to where the ground is half as high, at H/2.
- **x** is the horizontal distance from the crest to the building, upwind or downwind.

[Drawing: A 2D ridge or 3D hill in section with the wind from the left. Wind arrows show the approach wind getting faster with height, and the wind over the crest faster still, most of all near the ground. H is the height from the base to the crest, Lh runs upwind from the crest to the half-height point, and x runs from the crest to the house.]

A 2D ridge or 3D hill. The wind speeds up over the crest, most of all close to the ground.

[Drawing: A 2D escarpment in section with the wind from the left: low ground rising to a plateau. The wind is fastest just past the edge. H is the height of the rise, Lh runs upwind from the crest to the half-height point, x runs from the crest to the house, and z is the height above the ground at the house.]

A 2D escarpment. The ground stays high past the crest, so the speed-up reaches farther downwind (μ = 4).

## When K_zt applies

Section 26.8.1 sets five conditions. If any one of them isn't met, K_zt = 1.0.

1. The hill, ridge or escarpment is isolated: no similar feature of comparable height stands upwind of it within 100H or 2 miles, whichever is less, measured from the point where H is found.
2. It stands at least twice as high as the upwind ground features within 2 miles, in any quadrant.
3. The building is in the upper half of a hill or ridge, or near the crest of an escarpment.
4. H/L_h is at least 0.2. Gentler slopes don't speed the wind up enough to count.
5. H is at least 15 ft in Exposure C and D, or at least 60 ft in Exposure B.

This is why K_zt is 1.0 at most sites, and in most wind directions even at sites on a hill. The wind has to blow up the slope toward the building. Wind from behind the building, or along a ridge, gets no speed-up.

## The equations

K_zt = (1 + K_1 K_2 K_3)²

- **K_1** covers the shape of the hill and the largest speed-up: K_1 = (K_1/(H/L_h)) × H/L_h, with the multiplier from the table below.
- **K_2** covers the fall-off with distance from the crest: K_2 = 1 − |x| / (μ L_h), and 0 past μL_h.
- **K_3** covers the fall-off with height z above the local ground: K_3 = e^(−γz/L_h)

| Shape | K_1/(H/L_h) | γ | μ |  |  |  |
| --- | --- | --- | --- | --- | --- | --- |
| Exp. B | Exp. C | Exp. D | Upwind | Downwind |  |  |
| 2D ridge | 1.30 | 1.45 | 1.55 | 3 | 1.5 | 1.5 |
| 2D escarpment | 0.75 | 0.85 | 0.95 | 2.5 | 1.5 | 4 |
| 3D hill | 0.95 | 1.05 | 1.15 | 4 | 1.5 | 1.5 |

**Steep slopes:** when H/L_h is more than 0.5, use 0.5 for H/L_h in K_1, and use 2H in place of L_h in K_2 and K_3. The speed-up stops growing past that steepness, and it spreads over a distance set by the height instead of the slope.

## Worked example: a house on the Palisades

The Palisades are a line of cliffs along the west bank of the Hudson River, north of New York City. Take a house about 33 ft back from the cliff edge near State Line Lookout (40.9875° N, 73.9065° W), with a mean roof height of 30 ft, in Exposure C. The governing wind blows from the northeast, across the river and up the cliff. The numbers below come from the USGS elevation model through our [topographic factor calculator](https://webstructural.com/topographic-factor-calculator.html?lat=40.98750&lon=-73.90650&height=30&exposure=C), which shows the same site.

### Step 1: the shape

The ground rises from the river to the top of the cliff and stays high inland. That makes it a **2D escarpment**, and the house is downwind of the crest.

### Step 2: H, L_h and x

- The crest is at elevation 530 ft. The base is the river surface, at about −4 ft in the elevation model. H = 530 − (−4) = 534 ft
- The ground is at half height (H/2 = 267 ft above the base) 153 ft upwind of the crest, so L_h = 153 ft.
- The house is x = 33 ft downwind of the crest.

[Drawing: The ground at the Palisades site from the USGS elevation model, drawn to scale: the Hudson River at about −4 ft, the cliff rising to the crest at 530 ft, and the house 33 ft past the crest. H is 534 ft and the half-height point is 153 ft upwind of the crest.]

The ground along the wind at the site, from the USGS elevation model, drawn to scale.

### Step 3: the five conditions

- Isolated, and twice as high as upwind ground: upwind ground within 2 miles rises at most 114 ft above the base, under H/2 = 267 ft. ✓
- Near the crest of an escarpment: 33 ft back from the edge. ✓
- H/L_h = 534 / 153 = 3.5, at least 0.2. ✓
- H = 534 ft, at least 15 ft for Exposure C. ✓

One judgment call: ground to the side, within 2 miles, rises 366 ft above the base. That's the same line of cliffs running north and south, not a separate hill, so it doesn't make the cliff less isolated.

### Step 4: the steep-slope rule

H/L_h = 3.5 is more than 0.5, so K_1 uses H/L_h = 0.5, and K_2 and K_3 use 2H = 1,068 ft in place of L_h.

### Step 5: K_1, K_2 and K_3

K_1 = 0.85 × 0.5 = 0.425

K_2 = 1 − 33 / (4 × 1,068) = 0.992 (μ = 4 downwind of an escarpment)

K_3 = e^(−2.5 × 30 / 1,068) = 0.932

### Step 6: K_zt

K_zt = (1 + 0.425 × 0.992 × 0.932)² = 1.393² = 1.94

Velocity pressure is proportional to K_zt, so this house takes 94% more wind pressure than the same house on flat ground.

### K_zt by height

Only K_3 changes with height, so the speed-up fades higher up:

| Height z (ft) | K_3 | K_zt |
| --- | --- | --- |
| 15 | 0.966 | 1.98 |
| 30 | 0.932 | 1.94 |
| 50 | 0.890 | 1.89 |
| 100 | 0.791 | 1.78 |
| 200 | 0.626 | 1.60 |

K_1 = 0.425 and K_2 = 0.992 throughout.

[Drawing: Kzt against height above the ground for the Palisades example: 1.98 at 15 ft, 1.94 at 30 ft, 1.89 at 50 ft, 1.78 at 100 ft and 1.60 at 200 ft, falling toward 1.0 with height.]

K_zt for the Palisades house by height above the ground. Only K_3 changes.

## Finding K_zt from elevation data

Reading H, L_h and x off a contour map by hand takes time, and has to be done for every wind direction. The [topographic factor calculator](https://webstructural.com/topographic-factor-calculator.html) does it from the USGS 1/3 arc-second elevation model, which has a point about every 10 m across the US:

- Click the site on the map, or enter an address. It samples the ground along 16 wind directions, 2 miles upwind of each crest.
- In each direction it finds the crest, the base (the lowest ground before the slope rises again), L_h and x. It then guesses the shape, which Pro accounts can change.
- It checks the five conditions and shows each one passing or failing, with the reason.
- It shows the ground profile with the crest, half height and base marked, so you can check what it found.
- The governing K_zt and the ground elevation, which the wind load needs for K_e, go straight into the [wind load calculator](https://webstructural.com/wind-load-calculator.html).

![The calculator's ground profile for wind from the northeast: flat river, the cliff rising to 530 ft, with circles at the base, half height and crest and a triangle at the site.](https://webstructural.com/images/tutorials/kzt/calculator-profile.webp)

The ground profile the calculator draws for each direction, with the base, half height and crest it found, so you can check them.

Condition 2 says "in any quadrant". The calculator checks the ground upwind strictly. Rising ground to the side only shows a warning, because whether it's a separate hill or the same ridge, as in the example above, takes an engineer's judgment.

## Frequently asked questions

### What is K_zt on flat ground?

1.0. It's also 1.0 whenever any of the five conditions of section 26.8.1 isn't met.

### How large can K_zt get?

At the crest of a steep 2D ridge in Exposure D, close to the ground: (1 + 1.55 × 0.5)² ≈ 3.2. Near the edge of a steep cliff, as in the example, it's about 2.

### Is K_zt the same in every wind direction?

No. It depends on the ground the wind crosses, so each direction gets its own value. Design with the largest unless you check each wind direction on its own.

### Did K_zt change between ASCE 7-16 and ASCE 7-22?

The method in section 26.8 and Figure 26.8-1 is the same in both editions.

### What height z do I use for K_3?

The height above the local ground at the building. For a low-rise building's roof pressures it's usually the mean roof height. K_zt is largest near the ground, so a lower z is the cautious choice.

More worked examples: [browse all structural design tutorials](https://webstructural.com/structural-learning-hub.html).
